Voi come le lubrificate?

Ricarica,cartucce e polveri da sparo
Rispondi
Avatar utente
mainard
Settimo Livello
Settimo Livello
Messaggi: 717
Iscritto il: mar set 22, 21:15:12
Località: Pavullo nel Frignano

Voi come le lubrificate?

Messaggio da mainard »

Mi rivolgo a FAXBAT e LUCASB67 (maestri d'armi), ma in generale a tutti coloro che hanno in cassaforte pistole e revolver che non usano per diverso tempo; io oggi ho tirato fuori tutta la artiglieria e lubrificato , unto e passato il panno siliconato. Pero' non sono sicuro di aver operato bene! Le canne in particolare (pulite) le ho lasciate unte di BALLISTOL ! ho sbagliato? Dovevo lubrificarle con olio? :paura:
non nobis Domine,non nobis sed nomine tuo da gloriam.
Avatar utente
robbi
Quinto Livello
Quinto Livello
Messaggi: 516
Iscritto il: sab dic 19, 20:15:17
Località: molinella(bo)

Re: Voi come le lubrificate?

Messaggio da robbi »

io scarico la tensione delle molle a lamina S&W
al buio tutti i gatti son grigi
Avatar utente
Pyno&dyno
VERY SHOOTER-coppa argento
VERY SHOOTER-coppa argento
Messaggi: 11684
Iscritto il: mer ago 26, 11:23:00
Skype: pinoedino
Località: East Polentonia

Re: Voi come le lubrificate?

Messaggio da Pyno&dyno »

Io sulle canne ci metto il break free quando devono rimanere ferme per qualche mese
Because they said I couldn't have it
Avatar utente
Calico
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 9505
Iscritto il: mer feb 03, 12:50:17
Località: Toscana centrale - confine Maremma

Re: Voi come le lubrificate?

Messaggio da Calico »

:lol: Scusate la risata ma mi avete ricordato un episodio avvenuto oltre 30 anni fa: quando avevamo ancora l'armeria, i cfc negli spray non erano ancora fuori legge e poichè i primi oli spray costavano un occhio, rimanevano sullo scaffale per anni ed anni. Non si sa se per cattiva conservazione o se per un lotto difettoso, molti cacciatori eseguirono la lubrificazione dell'arma alla fine della stagione e, a stagione successiva SORPRESA! L'interno delle canne era ricoperto di ossido e la maggior parte di esse era rovinata irrimediabilmente :lol: Quell'anno ci fu il boom delle vendite di canne calibro 12 nelle città vicine.
Pentitevi!!!
davito
Quarto Livello
Quarto Livello
Messaggi: 465
Iscritto il: dom set 20, 23:42:58
Località: Bollate

Re: Voi come le lubrificate?

Messaggio da davito »

Ogni mese tiro fuori le armi e le ungo ben bene con l'olio Benelli MF-82 (ma credo che tutti gli olii per armi vadano bene).
La carabina la ripongo nella fuciliera così come mamma Howa l'ha fatta, le pistole le chiudo dentro i sacchetti che vengono utilizzati per congelare gli alimenti, sacchetti che oramai sono un olio unico anche loro.
La carabina sono due anni che non spara un colpo e non ha nessun segno di ossidazione.
Per chi dice che si può formare la condensa sentro i sacchetti, rispondo che l'arma più vecchia è da 17 anni che subisce questo trattamento e non ha il minimo segno di ruggine, pur non essendo costruita in acciaio inox. Ovviamente bisogna oliare bene anche i sacchetti.
Ciao, Davide.
Avatar utente
Pietro66
Settimo Livello
Settimo Livello
Messaggi: 798
Iscritto il: lun set 21, 12:24:31
Skype: pietrover66
Località: Legnano

Re: Voi come le lubrificate?

Messaggio da Pietro66 »

Le armi vanno lasciate il piu' possibile pulite e leggermente lubrificate, nei punti di scorrimento e di "lavoro" meccanico.
Leggermente unte, non ingrassate.
Aborro i grassi grafitati, grassi al rame, basta un velo di olio di vaselina, Ballistol, e parlo delle guide di scorrimento dei carrelli, oppure delle sedi di scorrimento degli otturatori, specie di carabine semiauto.

Ma la cosa piu' importante e' pulire, il piu' presto possibile, le morchie nere che una volta solidificate diventano dure da pulire.

Per le canne invece altro discorso:
una volta pulite per bene, scovolate con un bronzo fosforoso o rame, vanno si' lubrificate ma subito asciugate molto bene con una pezzuola che "dovrebbe" uscirne pulita.

Mai , e dico mai, sparare con una canna unta d'olio, potrebbe essere molto pericoloso, ma -soprattutto- non serve a nulla.
Per evitare formazioni di ruggine sulle armi vanno solo tenute in armadi e ambienti asciutti.
In dieci anni che tengo armi non mi e' mai capitato di vedere nemmeno un puntino di ruggine su un'arma.
Arrivera' baffone....
Sono su skype: pietrover66
Avatar utente
lucasb67
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2677
Iscritto il: lun set 21, 22:51:55
Località: Terre di Vini e Bevitori

Re: Voi come le lubrificate?

Messaggio da lucasb67 »

mainard ha scritto:Mi rivolgo a FAXBAT e LUCASB67 (maestri d'armi), ma in generale a tutti coloro che hanno in cassaforte pistole e revolver che non usano per diverso tempo; io oggi ho tirato fuori tutta la artiglieria e lubrificato , unto e passato il panno siliconato. Pero' non sono sicuro di aver operato bene! Le canne in particolare (pulite) le ho lasciate unte di BALLISTOL ! ho sbagliato? Dovevo lubrificarle con olio? :paura:


ti ringrazio della stima e apparentamento assolutamente immeritato con pasquale che ha veramente moltissima esperienza, se non per altro per l'età!!

:jumpy:

perdonami pasquale, ma sai che "il maestro", quello vero, deve sempre subire lo scherno degli alievi, anche quelli che indegnamente hanno fatto carriera

:birra:

tornando alla lubrificazione, c'è da dire che è assolutamente necessaria, quanto se non di più di una pulizia accurata dell'arma

con il tds ho imparato anche a trovare i limiti di questa "cura" necessaria, verificando proprio nelle stagioni più calde e nelle giornate più intense di tiro, quando l'arma arriva ad essere alla fine "troppo" asciutta, situazione ovviamente che farà "legare" i metalli sino a grippare e quindi usurarsi

con questa esperienza ho raggiunto una ricetta che per il momento mi soddisfa molto:

dopo la pulizia profonda dell'arma con semplice smontaggio da campagna, carrello, fusto e canna, fatti con bagnetto di petrolio bianco, spazzolino da denti vecchio ma con setole ancora nervose, e asciugatura con soffiaggio di aria compressa, inizio lubrificando con un piccolo pennello da aquerelli stendendo un velo di grasso al rame seguito da alcune goccie di break free in vari punt dove l'arma è sollecitata, interno del carrello dove scorre la canna in volata e sui tennoni e ramponi, zoccolo della canna, guide del fusto e carrello

con uno straccietto solo inumidito di ballistol, passo l'interno della canna con uno scovolo ... attenzione perchè un eccesso di olio in canna magari abbinato a munizionamento molto potente può provocare un innalzamento pressorio incontrollato

non vanno mai unti gli scatti che devono lavorare assolutamente a secco

se devo conservare l'arma a lungo in cassaforte uso stendere un velo di ballistol su tutta l'arma

uso il ballistol per la conservazione e per l'interno della canna perchè lo ritengo il miglior prodotto antiossidante
... fai bene tutto quello che sai fare e poi "lascia che il colpo ti racconti la sua storia!"
Avatar utente
waltherp38
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 5121
Iscritto il: ven set 18, 15:42:23
Località: Nuceria Alphaterna

Re: Voi come le lubrificate?

Messaggio da waltherp38 »

Cito da The gun zone.com

Rust Preventatives for Firearms

by Robert P. Firriolo

I am an anti-corrosion fanatic and a lubricant nut, ever in search of the best product to prevent rust and keep moving parts moving, whether on guns, on vehicles, or around the house and workshop. Maybe that's because when I make an investment in a firearm, a hand tool, a car, or whatever, I want it to last.

Over the years I have accumulated numerous products that claim to lubricate and prevent rust. Some are dedicated gun-care products, and others are household and automotive products.

So far, I have rarely been disappointed by one of these products so far as gun maintenance is concerned. But then again I will have to admit to being somewhat scrupulous about cleaning, lubing, and wiping down my guns with good a preservative to prevent rust.

Recently I was inspired by a home test performed by a fellow member of the Curio & Relic FFL E-mail list. This industrious chap tested a few products he had on hand to see how they prevented rust, and reported back to the list over the course of a week or so.

As fine a job as he did, he really didn't have too many products on hand to satisfy my own curious nature. After all, if all of the products I have used weren't tested, I wasn't happy.

Thanks to all of the recent rain we had where I live, I found myself one summer weekend running my own tests. My goal was simply to see what products, when applied as I use them on firearms, would stave off rust the longest.
Test 1: Single Dose Exposure
The first round of tests was designed to test the effectiveness of a relatively heavy coat of preservative with a single, heavy dose of salt spray. I figured this gave the products a fair chance to see if they could ward off moisture as might be encountered on a wet hunting trip or during a day where one's concealed carry handgun rides against a sweaty body.

The first test used 1½ inch bright finish nails, thoroughly cleaned with steel wool to remove surface oxidation until they were all shiny. All of the nails were then degreased with Kleen Bore Gunk Out spray, wiped with clean paper toweling while still wet, and then spray degreased again and patted dry with clean paper towels.

Thereafter, the nails were handled only with forceps that were cleaned and degreased. The test products were applied directly to the nails from the bottles or cans. If the product was a liquid, it was dripped from the top of the nail down to the bottom, making sure all sides were coated. Products in spray form were applied by spraying the nail as it was rotated, to ensure full coverage.

Whether spray or liquid, I purposely used more than enough of each product to ensure full coverage. Between applications, the forceps were degreased to prevent cross-contamination with other products while handling the nails.

After each nail was coated, the excess product was blotted off with a piece of clean paper towel. The object was to keep the nail wet, but not dripping, with the test product. Two polished, degreased nails remained uncoated with any product to serve as controls.

The products initially tested were:
Kleen Bore TW25-B
Break Free CLP

Break Free LP
Shooter's Choice Rust Prevent

Birchwood-Casey Sheath
Remington RemOil

Eezox
WD-40

Kano Kroil
3-in-One Household Oil

Sandaro Industries' Bore Cote
Miltec-1.

Sandaro Industries' Arms Cote


Each of the nails was placed on a sheet of wax paper that had been divided into a numbered grid with magic marker. Each nail had its own section of paper where it was not in contact with any other nail.

A saturated salt solution was then prepared in a clean spray bottle. In this case, Diamond Crystal Kosher salt (which is not iodized) was added to the water in the bottle until salt crystals started to precipitate out of the solution. A little more water was added to dissolve the precipitated salt, which got me pretty close to a saturated solution. I figure this was about as severe a test solution as I could concoct.

All of the nails were sprayed down until a small puddle formed around each one. Ambient temperature was a mostly constant 75°F, and relative humidity was around 65%.

The salt-sprayed test nails were allowed to air dry, and the results were observed periodically. After 22 hours, the test was stopped because the uncoated control nails had almost completely rusted, and 22 hours represents a generous amount of time between an ordinary exposure to moisture and one's opportunity to clean the exposed firearm.

The results appear below, in order of my subjective ranking of best-performing to worst:

Best:
Break Free CLP: No rust, bright.
Break Free LP: No rust, bright.
Eezox: No rust, bright.
Sheath: No rust, slight darkening.

Very Good:
TW25-B: Trace rust freckling, slight darkening.
RemOil: Slight rust freckling on bottom.
3-in-One Oil: Trace rust.
Bore Cote: Trace rust on bottom.
WD-40: One small area of rust.

Good:
Rust Prevent: Two small rust spots, <20% coverage.

Unsatisfactory:
Arms Cote: >50% rusted.
Miltec-1: Significant rust along bottom; rust freckling on top.
Kroil: >75% rusted.

The results of the first test produced two immediate thoughts. One was that my first test was probably tougher than most real-world scenarios, as I had been using some of the lower-ranked products for years and had never seen a spot of rust. The other thought was to wonder what would happen to the better products with long-term exposure to salt spray. This led to test number two.
Test 2: Repeated Exposure
The second test was designed to see how the products would hold up to repeated exposure to a corrosive environment, so I changed the test to alternate wetting and drying. I also wanted the product application to be lighter, to be representative of the type of wipe-down many people leave on a firearm exterior before carrying it afield or concealed.

Test two started with two-inch bright finish nails cleaned and polished with steel wool, and degreased even more thoroughly than in test one. This batch of test nails sat in a bath of degreaser for 10 minutes after their initial spray-down with Gunk-Out and wiping.

Proceeding under the same test conditions as in test one, each test product was applied to a nail by wetting a clean, cotton patch with the product, and then carefully wiping down all surfaces of the nail. The nail was then placed on its gridded portion on the same sheet of wax paper. Again, two untreated nails were used as controls.

The sheet of nails was then misted with the saturated salt solution until uniformly coated, but not so heavily as in test one. Interestingly, while the two control nails attracted the spray and pooled it alongside, all of the products but one seemingly repelled the moisture on the wax paper from the nails.

The second test brought back the more promising and popular products, plus a few additional ones: Hoppe's Lubricating (vintage 1970s), U.S. mil-spec "LSA" Medium Weapons Oil (made by Bray Oil Co.), and CRC 5-56 Lubricant. The latter is a spray commonly available in auto supply stores.

The test nails were allowed to dry, and the formation of salt crystals on all of the nails was then apparent. The nails were misted again with salt spray every five to six hours.

Observations were made after five (5) hours and after 29 hours. Again, I rank them according to my subjective observations:
Sustained Exposure After 5 hours After 29 hours
Best
Eezox No rust, bright No rust, bright
Break Free CLP No rust, bright No rust, bright
Excellent
Break Free LP No rust, bright Trace rust freckling
Very Good
LSA Medium Weapons Oil No rust, bright Some freckling, small rust spot
WD-40 Trace freckling Some rust freckling, few spots
Good
RemOil No rust, bright Some rust freckling
TW25-B No rust, bright Some rust spots and freckling
Fair
Rust Prevent Trace rust freckling Significant coverage with rust spots
Maybe
CRC 5-56 No rust, bright Freckling; rust strip 1/3 of bottom
Sheath Trace rust freckling Rust spots & freckling
Unsatisfactory
Hoppe's Lubricating Significant rust on bottom About 50% rust covered
3-in-One Oil Significant rust spots More than 50% rust covered

After noting my finding on the second test, I decided to see how long it would take to get Eezox and Break Free CLP treated metal to start to rust. I continued to mist the nails twice a day with the salt solution. Amazingly, after one full week, the Eezox nail was still bright and shiny, while the CLP started to show a mere trace of rust freckling. Clearly, Eezox was the winner of my tests, followed closely by CLP.

After writing up my notes on the second test, I returned to the work shop with my test nail sheet and decided that instead of unceremoniously dumping the nails… as I had done after the first test… I would see if I could get the CLP or Eezox to rust. Over the course of another week I misted the sheet with the same salt spray solution at least once, sometimes twice, a day. I was a little less scientific and methodical here, as this final round was sort of just for the heck of it.

Towards the end of the second week I started to notice some freckling on the CLP nail. By day seven of supplemental testing (and day 14 total), the CLP nail was starting to show light, but noticeable, rust coating most of the nail. Amazingly, the Eezox nail was still clean. It had a fair coating of salt crystals, but not even a trace of rust.

The test could have continued, but there was no point in doing so. Two weeks of repeated exposure to a heavy salt solution without cleaning and application of a preservative is a more extreme situation than any I can imagine finding with one of my guns.
Comments and Observations
I have used some of the products that finished fairly low in my rankings for years with no complaints. For example, although Birchwood-Casey Sheath finished near the bottom, I have used it for over ten years and haven't found anything it allowed to rust. This may mean my test was unrealistically harsh. But it also tells me which product is more likely to fail first under extreme conditions. So while I'll still use up the remainder of the Sheath and Rust Prevent I have on hand with confidence, I doubt I'll need to buy any more. CLP and/or Eezox alone will supplant my cabinet full of products.

Despite its good results, I would not use WD-40 for firearms unless I had little other choice. The "WD" stands for "water displacing," and WD-40 does that task well. That means it is good for hosing down and flushing out that duck gun that fell overboard, at least until you can get it home for a proper cleaning. However, WD-40 tends to gum and turn into a varnish with time. So WD-40 may be fine for an external wipe down, but it is potentially devastating to moving parts that require lubrication. In my experience, WD-40 has little, if any, lubricating properties, and is best left for its designed tasks.

Then there's the issue of lubrication. Most of the products tested claim to be lubricants. My tests do not predict in any way which will be a better lube than the other. The same goes for products that claim to be cleaning solvents as well.

Interestingly, the products that claim to be primarily rust preventatives finished lower than two "all-in-one" products. Both top-finishers Eezox and Break Free CLP claim to clean, lubricate, and prevent rust. Some people claim that do-it-all products cannot perform any one job particularly well. But now we know that they are wrong, at least as far as rust prevention is concerned. And I have found Break Free CLP, and to a lesser extent, Eezox, to be decent gun cleaning solvents except where metal fouling is present. Both have also been satisfactory lubricants in my over 10 years using them.

Another interesting observation that ran counter to my expectations involved Break Free LP. LP is, as you would expect, the same as CLP but without the cleaning compounds. This should mean that LP should lubricate and protect better than CLP, which is "diluted" with "C," the cleaning solvent. Maybe LP is a better lubricant than CLP, but it clearly is not a better preservative.

While many of the "premium" gun care products can be costly, one of the nice things about both top performers is that they can be bought in bulk-sizes. Buying pint or larger bottles of Eezox¹ and Break Free CLP can certainly cut costs over the more common smaller sizes.

And the best buy of all is CLP's military predecessor, LSA. LSA can often be found for $1.00 per four ounce bottle. While it is not a cleaning solvent, and I can't vouch for its lubricating properties, I would feel quite confident using it to prevent rust on any firearm. And considering I prefer to use a quality synthetic grease for the gun parts that need the most lubrication (e.g., bolt lugs, slide rails), LSA would likely suit my gun oil needs just fine.

Another consideration in choosing a gun care product is its affinity for dirt. That is, will it attract dirt, dust, pocket lint and other forms of crud? While 3-in-One oil showed that a thick coat will protect well in the short term, it would never be my choice for wiping down guns because it attracts dirt like a magnet. By contrast, Eezox, which mostly dries, and TW25-B, which can be wiped dry and still perform well, are much better at resisting dirt.
Conclusion
Lots of gun care and household products claim to prevent rust. Most do, to one extent or another. For routine use in normal situations, most of the products tested will serve just fine. I can say this because I have used these products over the years without encountering any rust problems.

But for those who are anticipating exposure to marine environments, wet weather, prolonged contact with sweat and skin acids, the higher-ranked products should provide that desired extra-margin of protection.

Finally, if you don't see a product you like, or are curious about, listed in my test, just follow a similar procedure and test it yourself! Salt water and nails (or strips of ferrous metal) are cheap and readily available. That way you can find out for yourself just what works, and what doesn't work. Just like I did.
L'ignorante parla a vanvera.L'intelligente parla al momento opportuno.Il saggio parla solo se interrogato.'O fess parla sempre -Principe Antonio De'Curtis-detto Totò.
-A well regulated militia being necessary to the security of a free state,
the right of the people to keep and bear arms shall not be infringed.

NORINCO proudly owner.
Avatar utente
waltherp38
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 5121
Iscritto il: ven set 18, 15:42:23
Località: Nuceria Alphaterna

Re: Voi come le lubrificate?

Messaggio da waltherp38 »

Anche questo articolo concorda con Pyno&dyno e altri membri del forum nel ritenere il Break Free il migliore lubrificante.

Al secondo posto il WD40 che adopero io, JigenGiò ed altri scalmanati. :birra:
L'ignorante parla a vanvera.L'intelligente parla al momento opportuno.Il saggio parla solo se interrogato.'O fess parla sempre -Principe Antonio De'Curtis-detto Totò.
-A well regulated militia being necessary to the security of a free state,
the right of the people to keep and bear arms shall not be infringed.

NORINCO proudly owner.
Avatar utente
lucasb67
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2677
Iscritto il: lun set 21, 22:51:55
Località: Terre di Vini e Bevitori

Re: Voi come le lubrificate?

Messaggio da lucasb67 »

... sarebbe interessante una traduzione, ma francesco, credimi, l'articolo sembra un po' confuso per quanto la fonte sia autorevole, in ogni caso bisogna sempre distinguere pulizia e quindi detergenti, in questo caso il wd40 penso possa andar bene anche se personalmente lo sconsiglio, in quanto mi è stato riferito da un analista di laboratorio che conterrebbe tracce di acqua per sciogliere alcune parti che ne compongono la miscela, e questo particolare combinato con i residui carboniosi darebbe vita ad acidi come il nitrico, molto corrosivo con tutti gli acciai anche gli inox ... per il resto trovo il wd40 un ottimo prodotto che anch'io ho usato a lungo anche per questo uso, ma ora non più

poi c'è la lubrificazione e in questo il wd40 è veramente "povero" per le armi, soprattutto con le alte temperature evapora velocemente
... fai bene tutto quello che sai fare e poi "lascia che il colpo ti racconti la sua storia!"
Avatar utente
waltherp38
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 5121
Iscritto il: ven set 18, 15:42:23
Località: Nuceria Alphaterna

Re: Voi come le lubrificate?

Messaggio da waltherp38 »

Azz Luca, nun ce lo sapevo...

Grazie per la dritta. :ok:

Mi sa che mi tocca munirmi di Break Free per la lubrificazione (uso deposito) dell'arma.

Nessuno di voi usa i sali essiccanti nella fuciliera?
L'ignorante parla a vanvera.L'intelligente parla al momento opportuno.Il saggio parla solo se interrogato.'O fess parla sempre -Principe Antonio De'Curtis-detto Totò.
-A well regulated militia being necessary to the security of a free state,
the right of the people to keep and bear arms shall not be infringed.

NORINCO proudly owner.
Avatar utente
lucasb67
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2677
Iscritto il: lun set 21, 22:51:55
Località: Terre di Vini e Bevitori

Re: Voi come le lubrificate?

Messaggio da lucasb67 »

io uso un mangia umidità, ma non ti so dire di che marca ... è in pratica un cubo con una poasticca che fa depositare l'umidità sul fondo del cubo

tornando alla lubrificazione il break free è ottimo, credo avvicinato per bontà solo dai migliori olii sintetici teflonati per motori ad alte prestazioni, ma anche lui, come ho scritto più su, in certe situazioni estreme volatilizza completamente e può lasciare l'arma completamente secca

per la conservazione credo che il migliore sia il ballistol che con l'evaporazione della parte volatile, lascia uno strato ceroso incredibilmente efficace nel tempo
... fai bene tutto quello che sai fare e poi "lascia che il colpo ti racconti la sua storia!"
Avatar utente
waltherp38
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 5121
Iscritto il: ven set 18, 15:42:23
Località: Nuceria Alphaterna

Re: Voi come le lubrificate?

Messaggio da waltherp38 »

:cinesino:

Rettifico! :ok:
L'ignorante parla a vanvera.L'intelligente parla al momento opportuno.Il saggio parla solo se interrogato.'O fess parla sempre -Principe Antonio De'Curtis-detto Totò.
-A well regulated militia being necessary to the security of a free state,
the right of the people to keep and bear arms shall not be infringed.

NORINCO proudly owner.
Avatar utente
lucasb67
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2677
Iscritto il: lun set 21, 22:51:55
Località: Terre di Vini e Bevitori

Re: Voi come le lubrificate?

Messaggio da lucasb67 »

:cinesino:
... fai bene tutto quello che sai fare e poi "lascia che il colpo ti racconti la sua storia!"
Avatar utente
JigenGiò
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2504
Iscritto il: lun nov 02, 13:51:30
Località: Roccapiemonte Salerno

Re: Voi come le lubrificate?

Messaggio da JigenGiò »

waltherp38 ha scritto::cinesino:

Rettifico! :ok:

Sabato prossimo si portrebbe fare il triangolo Montoro Inferiore, Mercato S. Severino, San Marzano sul Sarno,
così ci procuriamo l'olio Break Free :cinesino:
Vivi meglio che puoi, pensa meglio che puoi e fa del tuo meglio.....oggi

L'arma carica non è pericolosa, l'arma scarica è pericolosa
Avatar utente
lucasb67
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2677
Iscritto il: lun set 21, 22:51:55
Località: Terre di Vini e Bevitori

Re: Voi come le lubrificate?

Messaggio da lucasb67 »

... ultima cosa, che però "tra le righe" già avevo esternato ... un valido sostituto al break free è un qualsiasi olio sintetico addizionato di teflon per motori ad alte prestazioni ... magari il vostro paesano che ancora non lavora alla ferrari può aiutarvi nella ricerca del prodotto ...
... fai bene tutto quello che sai fare e poi "lascia che il colpo ti racconti la sua storia!"
Avatar utente
faxbat
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 4212
Iscritto il: sab ago 22, 10:35:32
Località: Emilia Romagna

Re: Voi come le lubrificate?

Messaggio da faxbat »

lucasb67 ha scritto:io uso un mangia umidità, ma non ti so dire di che marca ... è in pratica un cubo con una poasticca che fa depositare l'umidità sul fondo del cubo

tornando alla lubrificazione il break free è ottimo, credo avvicinato per bontà solo dai migliori olii sintetici teflonati per motori ad alte prestazioni, ma anche lui, come ho scritto più su, in certe situazioni estreme volatilizza completamente e può lasciare l'arma completamente secca

per la conservazione credo che il migliore sia il ballistol che con l'evaporazione della parte volatile, lascia uno strato ceroso incredibilmente efficace nel tempo

Luca, se proprio vuoi usare un prodotto per deumidificare, lascia perdere assolutamente quel "CUBO" che contiene Calcio Cloruro ( la pasticca ). Il Calcio Cloruro e' un prodotto "deliquescente", cioe' a mano a mano che cattura l'umidita' da solido si trasforma in una specie di oliaccio....che purtroppo e' altamente corrosivo come tutti i cloruri ( per es quello che si forma dai vecchi inneschi a fulminato di mercurio miscelato con Potassio Clorato...da qui il Potassio Cloruro=corrosivo ).
Quello che ti consiglio invece e' il Gel di Silice che si vende anche in quantita' industriali ( e' sotto forma di cristalli bianchi trasparenti, a volte colorato in Bleu brillante perche' additivato di tracce di Cobalto cloruro che e' bleu quando e' secco, ma diventa rosa quando ha catturato un bel po' di umidita' ). Caratteristiche del Gel di Silice e' che e' inerte ( non reagisce coi metalli ) e che si puo' rigenerare. Si mette in una vaschetta di vetro pyrex o ceramica e quindi in stufa a 110°C finche' non diventa di nuovo bleu.
E' quello stesso che mettono nei sacchettini che accompagnano le ottiche etc. Per sapere dove comprarlo con "quattro" soldi domanda a Paolone.
Ultima modifica di faxbat il lun apr 12, 13:53:23, modificato 1 volta in totale.
"Se non hai una spada, vendi il tuo mantello e comprane una"
( Luca, 22-36 )
Avatar utente
lucasb67
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2677
Iscritto il: lun set 21, 22:51:55
Località: Terre di Vini e Bevitori

Re: Voi come le lubrificate?

Messaggio da lucasb67 »

:oops:


grazie pasquale, lo farò subito ... in effetti il cubo è frutto di un eccesso di zelo e ignoranza pazzesca in materia ... evidentemente!!

:love:
... fai bene tutto quello che sai fare e poi "lascia che il colpo ti racconti la sua storia!"
Avatar utente
mainard
Settimo Livello
Settimo Livello
Messaggi: 717
Iscritto il: mar set 22, 21:15:12
Località: Pavullo nel Frignano

Re: Voi come le lubrificate?

Messaggio da mainard »

lucasb67 ha scritto::oops:


grazie pasquale, lo farò subito ... in effetti il cubo è frutto di un eccesso di zelo e ignoranza pazzesca in materia ... evidentemente!!

:love:

Io mi sono fatto "mettere da parte" dalle mie amiche :risata: del negozio di vestiti sotto casa una quantita' industriale di quelle bustine che si trovano nelle confezioni e che loro buttano via e ci ho riempito la fuciliera.... loro mi danno i sali ed io le pastarelle..................(i sali non sono quelli per rianimarmi......magari ,visto che sono tutte bbbbbone) :jumpy:
non nobis Domine,non nobis sed nomine tuo da gloriam.
Avatar utente
Calico
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 9505
Iscritto il: mer feb 03, 12:50:17
Località: Toscana centrale - confine Maremma

Re: Voi come le lubrificate?

Messaggio da Calico »

Lucasb, mannaggiattè :lol: ora mi tocca togliere il wd-40 dagli scatti :P
Pentitevi!!!
Avatar utente
waltherp38
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 5121
Iscritto il: ven set 18, 15:42:23
Località: Nuceria Alphaterna

Re: Voi come le lubrificate?

Messaggio da waltherp38 »

mainard ha scritto:
lucasb67 ha scritto::oops:


grazie pasquale, lo farò subito ... in effetti il cubo è frutto di un eccesso di zelo e ignoranza pazzesca in materia ... evidentemente!!

:love:

Io mi sono fatto "mettere da parte" dalle mie amiche :risata: del negozio di vestiti sotto casa una quantita' industriale di quelle bustine che si trovano nelle confezioni e che loro buttano via e ci ho riempito la fuciliera.... loro mi danno i sali ed io le pastarelle..................(i sali non sono quelli per rianimarmi......magari ,visto che sono tutte bbbbbone) :jumpy:


e queste amiche bone quand'è che le metti un pò a giro, a servizio della comunità? :primo:
L'ignorante parla a vanvera.L'intelligente parla al momento opportuno.Il saggio parla solo se interrogato.'O fess parla sempre -Principe Antonio De'Curtis-detto Totò.
-A well regulated militia being necessary to the security of a free state,
the right of the people to keep and bear arms shall not be infringed.

NORINCO proudly owner.
Avatar utente
mainard
Settimo Livello
Settimo Livello
Messaggi: 717
Iscritto il: mar set 22, 21:15:12
Località: Pavullo nel Frignano

Re: Voi come le lubrificate?

Messaggio da mainard »

waltherp38 ha scritto:
mainard ha scritto:
lucasb67 ha scritto::oops:


grazie pasquale, lo farò subito ... in effetti il cubo è frutto di un eccesso di zelo e ignoranza pazzesca in materia ... evidentemente!!

:love:

Io mi sono fatto "mettere da parte" dalle mie amiche :risata: del negozio di vestiti sotto casa una quantita' industriale di quelle bustine che si trovano nelle confezioni e che loro buttano via e ci ho riempito la fuciliera.... loro mi danno i sali ed io le pastarelle..................(i sali non sono quelli per rianimarmi......magari ,visto che sono tutte bbbbbone) :jumpy:


e queste amiche bone quand'è che le metti un pò a giro, a servizio della comunità? :primo:

Gia', ma come le "immortalo" con la "wife" :mattarello: alle calcagna? :wife:
non nobis Domine,non nobis sed nomine tuo da gloriam.
Avatar utente
waltherp38
BEST SUPPORTER-coppa bronzo
BEST SUPPORTER-coppa bronzo
Messaggi: 5121
Iscritto il: ven set 18, 15:42:23
Località: Nuceria Alphaterna

Re: Voi come le lubrificate?

Messaggio da waltherp38 »

Per la wife c'è il radiolone...lui se magna tutto, non aver paura.

E, nel mentre il nostro eroe tiene a bada la consorte, noi ci facciamo prendere le misure del cavallo dalle operatrici del settore :risata:
L'ignorante parla a vanvera.L'intelligente parla al momento opportuno.Il saggio parla solo se interrogato.'O fess parla sempre -Principe Antonio De'Curtis-detto Totò.
-A well regulated militia being necessary to the security of a free state,
the right of the people to keep and bear arms shall not be infringed.

NORINCO proudly owner.
Avatar utente
mainard
Settimo Livello
Settimo Livello
Messaggi: 717
Iscritto il: mar set 22, 21:15:12
Località: Pavullo nel Frignano

Re: Voi come le lubrificate?

Messaggio da mainard »

waltherp38 ha scritto:Per la wife c'è il radiolone...lui se magna tutto, non aver paura.

E, nel mentre il nostro eroe tiene a bada la consorte, noi ci facciamo prendere le misure del cavallo dalle operatrici del settore :risata:

:risata: :risata: :risata: Fantastico Walt, mi scompiscio :risata: :risata: : :risata:
non nobis Domine,non nobis sed nomine tuo da gloriam.
Avatar utente
JigenGiò
SPECIAL MEMBER
SPECIAL MEMBER
Messaggi: 2504
Iscritto il: lun nov 02, 13:51:30
Località: Roccapiemonte Salerno

Re: Voi come le lubrificate?

Messaggio da JigenGiò »

waltherp38 ha scritto:Per la wife c'è il radiolone...lui se magna tutto, non aver paura.

E, nel mentre il nostro eroe tiene a bada la consorte, noi ci facciamo prendere le misure del cavallo dalle operatrici del settore :risata:

Attento te che siamo messi già male :???:
Se si registano le nostre donne... finisce la sparicchiata domenicale....
ne fanno loro una sola e a casa :paura: :paura: :paura:
Vivi meglio che puoi, pensa meglio che puoi e fa del tuo meglio.....oggi

L'arma carica non è pericolosa, l'arma scarica è pericolosa
Rispondi